Friday, August 2, 2013

Punch Art Baby Stroller

Hi Stampers,
Ready for a little Punch Art Project?  This is so fun to make...
 
(My inspiration for this card came from Brandy Cox. )
 
Supplies:
Real Red Paper #102482 
  • 5-1/2” x 8-1/2” (for base of card) scored @ 4 1/4”
  • 2” x 7” (for the scallops)
  • 3” x 3” (for small mitten and 2 Jewelry tags)
Whisper White Paper #100730
  • 3-3/4” x 5” (for embossing folder for layer 2 of card front)
  • 2” x 7” (for the scallops)
  • 3” x 3” (for the two 1-1/4” circles, the 1/16” heart, and the (2)-Itty Bitty punch outs for the wheel spokes.
Blushing Bride Paper #131198
  • 4” x 5-1/4” (for layer 1 card front)
  • 3-1/4” x 3-1/4” (for the (2) 1” Circles
  • 3-1/4” x 3-1/4” (for the large 2 ¾” circle from framelits) 

Big Shot Machine #113439

Square Lattice Embossing Folder #119976

Circles Collection Framelits #130911 (#6 counting from smallest to largest)

1” Circle Punch #119868

1-1/4” Circle Punch #119861

Jewelry Tag Punch #117190(retired)

Itty Bitty Shapes Punch Pack  #118309 (used the petal shaped one)
 
Mitten Builder Punch #127824 (retired)
 
Scallop Edge Border #119882
 
Pearl Basic Jewels (2-2mm, 1-3mm) #119247
 
Dimensionals #104430
 
Well Scripted Stamp Brush Set - Digital MDS Download #121064  cut at (3” x 1”)
 
1/16” - Small Heart Punch by Fiskars
 
6” of White Nylon Tulle for bow (6” piece)
 
Real Red Ink #126949 for sponge edges
 
Directions: 

Card Base
1. For card base, use Real Red paper 5-1/2” x –8-1/2”, score at 4-1/4”

2. For layer one, use Blushing Bride Paper to 4”x 5-1/4”

3. For layer two, use Whisper White Paper to 3-3/4” x 5”

Stroller
4. Using the 3-1/4” x 3-1/4” piece of Blushing Bride paper and from that piece cut out the 2-3/4” circle form the Circles Framelits Collection”, it will be the #6 die cut when counting out from center circle.
 5. Lightly pencil the 2-3/4” circle into four sections of pie by measuring inward 1-3/8” both sides to get to the middle point.  Now cut out 1/4 of the pie.
 
6. Take the 2” x 7” pieces of both the Real Red paper and the Whisper White paper.  On long edge of each of the strips, punch the whole 7” length with the Scallop Edge Border on both the white and red papers.  Now from scalloped edge measure in 1/2”, mark lightly, and cut both papers on that marked line so you have two scalloped pieces that are now 7” x 1/2" in size.
 
7. Line up both pieces on top of one another matching up the scallops, then mark and cut off a 2” piece to use for the top of the stroller hood and the leftover 5” piece will be use for the bottom part of the stroller. 
8. Glue the 2” Real Red scallop piece under the top part of the stroller staying very close to edge of the edge of the circle allowing the scallop to run past the top of canopy. Now glue the Whisper White scallop (matching the scallops design) to the Real Red scallop about half the width so Real Red shows nicely under the Whisper White scallop, once again allow it to run past the top of the canopy top.  Now trim off the excess scallop to match the shape of the top of the circle.   
Wheels
9. Using the 3” x 3” Whisper White cardstock and the 1-1/4” circle punch, cut out (2) circles of Whisper White.  (Save this scrap for later for the white heart for wheels in step #14)
 
10. Using the 3-1/4” x 3-1/4” Blushing Bride Paper, and the 1” circle punch, cut out 2 circles of Blushing Bride.
 
11. Using the 3” x 3” piece Real Red Cardstock piece, use the Jewelry tag punch to cut out 2 tags of Real Red and glue them together just before the rounded point of the tag.  (Save this scrap for small mitten punch out for later for the mitten step#15)
 
12. Using the scrap from the saved 3” x 3” piece Whisper White Cardstock from step #9, use the Itty Bitty Shapes Punch Pack (petal shaped one) and punch out (2) pieces of Whisper White for the wheel spokes.
 
13. Glue the Blushing Bride wheel on top of the Whisper White Wheel part and top with a 3mm Pearl Basic Jewel.  Repeat for both wheels.
 
14. Using the scrap from the above  3” x 3” piece Whisper White Cardstock  from step #9, punch out a small Whisper White heart from the 1/16” - Small Heart Punch by Fiskars and glue to the center of the now joined Jewelry Tags. 
 
15. Place (1) 2mm Pearl Basic Jewel to each outer side of the red jewelry tag. 
 
16. Glue the jewelry tag to connect both sets of wheels.
 
17. Using the saved scrap from the 3” x 3” piece of Real Red Cardstock from step #11, use the Mitten Builder Punch to punch out the small mitten topper, and cut out and shape the inside leaving one scallop to form a handle.
 
18. Place one 3mm pearl into top of handle.
 
19. Tie the 6 inches of tulle into a knot and glue dot it to the stroller when the canopy meets the stroller.
 
20. Trim ends to 1-1/2” each on an angle.
 
21.Attach the stroller and sentiment to card base with dimensional. Attach the wheels flat to the card without dimensionals.

Thank you so much for viewing my cards and for taking the time to leave me your comments! I read all of them, and I sincerely appreciate all of them!

If you would like to automatically get my blog posts by email all you have to do is enter your email address in the upper right hand corner of my blog where it says "follow me by email" then you'll never miss a a card or project again.

You can purchase supplies for this card and all my projects on my online Stampin' Up! Website by clicking the Shop 24/7 link below.


No comments:

Post a Comment

Thank You so much for taking the time to leave your comment!